How to build Prusa 2
|
English • العربية • български • català • čeština • Deutsch • Ελληνικά • español • فارسی • français • hrvatski • magyar • italiano • română • 日本語 • 한국어 • lietuvių • Nederlands • norsk • polski • português • русский • Türkçe • українська • 中文（中国大陆） • 中文（台灣） • עברית • azərbaycanca • |
Contents
- 1 Introduction
- 2 Assembly 1 (Frame Sides)
- 3 Assembly 2 (Frame Rear)
- 4 Assembly 3 (Frame Front)
- 5 Assembly 4 (Frame Top)
- 6 Assembly 5 (Frame Tightening)
- 7 Assembly 6 (Y Axis)
- 8 Assembly 7 (MDF Bed)
- 9 Assembly 8 (Y Axis Belts)
- 10 Assembly 9 (X and Z Axis)
- 11 Assembly 10 (Z Axis)
- 12 Assembly 11 (Heatbed)
- 13 Assembly 12 (Heatbed Thermistor)
- 14 Assembly 13 (jhead Hotend)
- 15 Assembly 14 (Extruder)
- 16 Assembly 15 (X Carriage)
- 17 Assembly 16 (X Axis Belts)
- 18 Assembly 17 (End Stops)
- 19 Assembly 18 (Printrboard Part 1)
- 20 Assembly 19 (Printrboard Part 2)
- 21 Assembly 20 (Printrboard Software)
- 22 Assembly 21 (Ramps 1.4 Software)
- 23 Assembly 22 (Bed Height Calibration)
- 24 Assembly 23 (Stepper Motor Calibration)
- 25 Assembly 24 (Extruder and First Print)
Introduction
You will find a list of 24 videos on this page. Each video was created to demonstrate the assembly process for the Prusa Mendel Iteration 2. It was intended to show every step from beginning to end without cutting out any parts. Thus the recordings account for 8 hours of videos. The videos may show more than you need, but that's alright, just skip to what you need to see. Also, the videos are in full HD (1080P), so if you have trouble seeing a detail, switch the quality setting.
Here is a video showing the parts and tools you'll need:
<videoflash>-DeHK80jcqzM</videoflash>
Assembly 1 (Frame Sides)
<videoflash>0xUi2MIsOhs</videoflash>
Assembly 2 (Frame Rear)
<videoflash>mADFyHpbnFU</videoflash>
Assembly 3 (Frame Front)
<videoflash>eII5YyETRkA</videoflash>
Assembly 4 (Frame Top)
<videoflash>VrNVsNgLLZU</videoflash>
Assembly 5 (Frame Tightening)
<videoflash>-ZWfqPOoWLw</videoflash>
Assembly 6 (Y Axis)
<videoflash>g_LG_wJiwIw</videoflash>
Assembly 7 (MDF Bed)
<videoflash>kJqolMN8_yc</videoflash>
Assembly 8 (Y Axis Belts)
<videoflash>Kz0MBiO5JFo</videoflash>
Assembly 9 (X and Z Axis)
<videoflash>rK3Nq4qfA-g</videoflash>
Assembly 10 (Z Axis)
<videoflash>gP1aCAzjlKY</videoflash>
Assembly 11 (Heatbed)
<videoflash>SSeaIJXmCKU</videoflash>
Assembly 12 (Heatbed Thermistor)
<videoflash>N9mWPjY-acg</videoflash>
Assembly 13 (jhead Hotend)
<videoflash>i7-VlQREPbo</videoflash>
Assembly 14 (Extruder)
<videoflash>LTmwnEahT5Q</videoflash>
Assembly 15 (X Carriage)
<videoflash>k2enMNvmPmg</videoflash>
Assembly 16 (X Axis Belts)
<videoflash>2n7HoT8zuxg</videoflash>
Assembly 17 (End Stops)
<videoflash>sd1slPTLl1U</videoflash>
Assembly 18 (Printrboard Part 1)
<videoflash>mW09_iZO3y8</videoflash>
Assembly 19 (Printrboard Part 2)
<videoflash>03Wb1HLRJfA</videoflash>
Assembly 20 (Printrboard Software)
<videoflash>I2bQ_QnY9cc</videoflash>
Assembly 21 (Ramps 1.4 Software)
<videoflash>j5RzXVzZ3DY</videoflash>
Assembly 22 (Bed Height Calibration)
<videoflash>TzEDT0vAIgw</videoflash>
Assembly 23 (Stepper Motor Calibration)
<videoflash>NvUOOz6SO-0</videoflash>
Assembly 24 (Extruder and First Print)
<videoflash>uWsD0bCdEyo</videoflash>
