File list
This special page shows all uploaded files.
| Date | Name | Thumbnail | Size | Description | Versions |
|---|---|---|---|---|---|
| 02:30, 24 November 2016 | Pandora overall.jpg (file) |  |
478 KB | Reverted to version as of 06:25, 24 November 2016 | 3 |
| 02:09, 24 November 2016 | Print overhang test.jpg (file) |  |
535 KB | Printing an overhang test piece on the glass bed. The IR Z-probe can be seen. | 1 |
| 01:37, 24 November 2016 | Silicone heaters 2.jpg (file) |  |
308 KB | Heat plate mounted on bed frame, resting on balsa strips for insulation. | 1 |
| 22:11, 23 November 2016 | Silicone heaters 1.jpg (file) |  |
1.01 MB | 240V Silicone heaters mounted on one of the four heat plates. | 1 |
| 03:45, 5 September 2016 | Pandora first print 2.jpg (file) |  |
376 KB | Printing a snowflake. | 1 |
| 03:44, 5 September 2016 | Pandora first print.jpg (file) |  |
162 KB | Printing a snowflake. | 1 |
| 23:05, 2 August 2016 | Rambo board.jpg (file) |  |
471 KB | Rambo board in enclosure. | 1 |
| 20:49, 2 August 2016 | Counterweight pulleys.jpg (file) |  |
569 KB | Pulley block for counterweight. | 1 |
| 20:39, 2 August 2016 | Idler rollers.jpg (file) |  |
336 KB | Idler rollers for CoreXY belts. | 1 |
| 20:37, 2 August 2016 | Zaxis motor.jpg (file) |  |
608 KB | The parts for the top bearing for the driven leadscrew (with Mena17 motor) | 1 |
| 20:36, 2 August 2016 | Zaxis idler.jpg (file) |  |
529 KB | The parts for the top bearing for the Z-axis leadscrew. | 1 |
| 20:35, 2 August 2016 | Zaxis home pos.jpg (file) |  |
285 KB | The bed is homed (as shown by the LED on the endstop switch) | 1 |
| 02:37, 4 June 2016 | Carriage with belts.jpg (file) |  |
298 KB | 1 | |
| 02:37, 4 June 2016 | Carriage with belts and motor.jpg (file) |  |
308 KB | 1 | |
| 02:36, 4 June 2016 | Carriage parts.jpg (file) |  |
278 KB | 1 | |
| 01:56, 24 May 2016 | Overall frame.jpg (file) |  |
692 KB | Overall view of frame, with tension cables on three sides. The front is left open. | 1 |
| 01:55, 24 May 2016 | Motor plate low.jpg (file) |  |
218 KB | Nema23 motor plate for low belt. | 1 |
| 01:54, 24 May 2016 | Motor plate high 2.jpg (file) |  |
223 KB | Nema23 motor plate for high belt, mounted up on spacers. | 1 |
| 01:53, 24 May 2016 | Gantry plate 3.jpg (file) |  |
213 KB | Gantry plate with angle connector. | 1 |
| 01:53, 24 May 2016 | Gantry plate 2.jpg (file) |  |
242 KB | Gantry plate with angle connector bracing it. | 1 |
| 01:52, 24 May 2016 | Gantry plate 1.jpg (file) |  |
226 KB | Plate at end of gantry. Two rollers have eccentric spacers allowing fine adjustment. | 1 |
| 01:51, 24 May 2016 | Frame.jpg (file) |  |
53 KB | Reverted to version as of 19:27, 16 August 2010 | 3 |
| 01:50, 24 May 2016 | Corner.jpg (file) |  |
271 KB | Top corner plate showing two idler wheels for the CoreXY belts, and one end of the gantry. | 1 |
| 01:49, 24 May 2016 | Corner plate.jpg (file) |  |
247 KB | This corner plate is sold to help build square-section steel shelving. It just happens to be a perfect fit for 20mm square V-slot. There is even a little hole for the tension cable end! | 1 |
| 01:47, 24 May 2016 | Corner plate 2.jpg (file) |  |
620 KB | Corner plate in place at top of frame. Note swaged stainless-steel cable end. | 1 |
| 01:45, 24 May 2016 | Bottle screw.jpg (file) |  |
585 KB | The bottle screw used to tension up the cables and hold the frame square. These parts are stainless-steel cables etc. used in balustrades. | 1 |
| 01:44, 24 May 2016 | Bed leadscrew notch.jpg (file) |  |
672 KB | Another view of the corner of the bed frame. The notch will allow the bed to be easily lifted clear of the leadscrew. | 1 |
| 01:42, 24 May 2016 | Bed frame.jpg (file) |  |
576 KB | Overall picture of bed frame. | 1 |
| 01:42, 24 May 2016 | Bed corner wheel.jpg (file) |  |
561 KB | Wheel at corner of bed, engaged with the V-slot leg. | 1 |
| 01:41, 24 May 2016 | Bed 2.jpg (file) |  |
738 KB | Bed sitting in frame. | 1 |
| 01:40, 24 May 2016 | Bed 1.jpg (file) |  |
653 KB | Bed sitting in frame. The leadscrews are not in place yet. | 1 |
| 06:12, 13 May 2016 | Top frame.jpg (file) |  |
363 KB | Top frame with gantry in place. V-slots are 1000mm by 700mm. | 1 |
