All public logs
Combined display of all available logs of RepRap. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).
(newest | oldest) View (newer 20 | older 20) (20 | 50 | 100 | 250 | 500)- 01:55, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel Y Motor End Spacer 1a.jpg (These spacers have been printed in PLA.)
- 01:54, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel Y Motor End Spacer 3a.jpg (Spacers for M3 screws, 10mm tall, bought at an electronics shop nearby. Shown here with a 20mm hex screw.)
- 15:51, 8 December 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel Y-axis motor end 10a.JPG (The Y-axis motor and GT2 pulley installed.)
- 03:47, 8 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis idler end 1a.JPG (The P3Steel Y-axis idler assembly.)
- 21:23, 3 December 2014 AndrewBCN (talk | contribs) uploaded File:PRUSA i3 steel 3mm lasercut 2.01 irobri.jpg (Prusa P3Steel version 2.01.)
- 21:13, 3 December 2014 AndrewBCN (talk | contribs) uploaded File:PRUSA i3 steel 3mm lasercut 2.01d irobri.dwg (CAD file for Prusa P3Steel, version 2.01. This is released under the same license as Irobri's original .dwg CAD file for version 2.0.)
- 13:17, 2 December 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel LCD2004 Controller 2a.jpg (An LCD 2004 Smart Controller installed on a P3Steel.)
- 10:42, 2 December 2014 AndrewBCN (talk | contribs) uploaded File:ATX cable extension 24 fem to male 1a.jpg (ATX PSU 24 pin motherboard cable extension required to connect to our 3D printer without modifying the ATX PSU.)
- 13:42, 23 November 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel heatbed adjust thumbwheel 1a.jpg (The essential heatbed leveling thumbwheel here shown installed.)
- 03:30, 23 November 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel-smooth rods 1a.jpg (Smooth rods (8mm stainless steel), unfinished and finished.)
- 16:23, 22 November 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel electronics 1a.JPG (Arduino Mega 2560 + Ramps 1.4 + A4998 drivers + 80mm fan + 12864 graphics LCD controller.)
- 07:18, 22 November 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis motor end 4a.JPG (Use 2 x 8mm M3 screws to attach the stepper to the support part. Insert the pulley oriented as shown but do not screw it yet.)
- 06:56, 22 November 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis motor end 3a.JPG (The wrong way to do it (by trial and error, where each try means filing away some more of the stepper).)
- 18:48, 21 November 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis motor end 2a.JPG (This nut interferes with the stepper.)
- 18:37, 21 November 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis motor end 1a.JPG (The left Y motor end support installed.)
- 17:20, 21 November 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis done 1a.JPG (Y-axis assembly minus the GT2 belt.)
- 17:18, 21 November 2014 AndrewBCN (talk | contribs) uploaded File:Tools 3a.JPG (A small hammer.)
- 17:18, 21 November 2014 AndrewBCN (talk | contribs) uploaded File:Tools 2a.JPG (M8 hex key and 14mm wrench.)
- 17:14, 21 November 2014 AndrewBCN (talk | contribs) uploaded File:Tools 1a.JPG (A small metal file and M3 hex key.)
- 17:02, 21 November 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel frame base underside.jpg (P3Steel frame foot with felt pad.)