User contributions
(newest | oldest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)
- 05:01, 25 October 2019 (diff | hist) . . (+410) . . G-code (→G28: Move to Origin (Home))
- 06:40, 23 October 2019 (diff | hist) . . (-1) . . G-code (→M908: Control digital trimpot directly)
- 06:34, 23 October 2019 (diff | hist) . . (+16) . . G-code (→M907: Set digital trimpot motor)
- 06:32, 23 October 2019 (diff | hist) . . (+16) . . G-code (→M900 Set Linear Advance Scaling Factors)
- 06:23, 23 October 2019 (diff | hist) . . (-1) . . G-code (→M666: Set delta endstop adjustment)
- 06:16, 23 October 2019 (diff | hist) . . (+15) . . G-code (→M416: Power loss)
- 06:14, 23 October 2019 (diff | hist) . . (-1) . . G-code (→M406: Filament Sensor off)
- 06:13, 23 October 2019 (diff | hist) . . (-1) . . G-code (→M405: Filament Sensor on)
- 05:59, 23 October 2019 (diff | hist) . . (+1) . . G-code (→M206: Offset axes)
- 05:38, 23 October 2019 (diff | hist) . . (+6) . . G-code (→M121: Disable endstop detection)
- 05:37, 23 October 2019 (diff | hist) . . (+6) . . G-code (→M120: Enable endstop detection)
- 05:31, 23 October 2019 (diff | hist) . . (-1) . . G-code (→M117: Display Message)
- 05:11, 23 October 2019 (diff | hist) . . (+16) . . G-code (→M113: Host Keepalive)
- 05:08, 23 October 2019 (diff | hist) . . (+75) . . G-code (→M111: Set Debug Level)
- 04:57, 23 October 2019 (diff | hist) . . (+251) . . G-code (→M86: Set Safety Timer)
- 04:52, 23 October 2019 (diff | hist) . . (+201) . . G-code (→M18: Disable all stepper motors)
- 04:48, 23 October 2019 (diff | hist) . . (+393) . . G-code (→M84: Stop idle hold)
- 04:32, 23 October 2019 (diff | hist) . . (+114) . . G-code (→M80: ATX Power On)
- 04:28, 23 October 2019 (diff | hist) . . (+550) . . G-code (→M73: Set build percentage)
- 04:19, 23 October 2019 (diff | hist) . . (+909) . . G-code (→M48: Measure Z-Probe repeatability)
- 04:23, 21 October 2019 (diff | hist) . . (+4,313) . . m G-code
- 02:19, 21 October 2019 (diff | hist) . . (+7) . . G-code (→M29: Stop writing to SD card)
- 02:18, 21 October 2019 (diff | hist) . . (-112) . . G-code (→M17: Enable/Power all stepper motors)
- 13:26, 20 October 2019 (diff | hist) . . (+16) . . m G-code (→M31: Output time since last M109 or SD card start to serial)
- 13:19, 20 October 2019 (diff | hist) . . (+87) . . m G-code (→M29: Stop writing to SD card)
- 13:14, 20 October 2019 (diff | hist) . . (+134) . . m G-code (→M17: Enable/Power all stepper motors)
(newest | oldest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)