User contributions
(newest | oldest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)
- 19:17, 12 November 2018 (diff | hist) . . (+119) . . G-code (Settled on a single M412 code)
- 18:22, 12 November 2018 (diff | hist) . . (+701) . . G-code (Add M410 Quick Stop)
- 17:54, 12 November 2018 (diff | hist) . . (0) . . G-code (Change M409 to M412)
- 17:53, 12 November 2018 (diff | hist) . . (0) . . G-code (Change M408 to M411)
- 05:36, 12 November 2018 (diff | hist) . . (+2) . . m G-code (→M409: Disable Filament Runout Sensors)
- 05:36, 12 November 2018 (diff | hist) . . (+2) . . m G-code (→M408: Enable Filament Runout Sensors)
- 05:35, 12 November 2018 (diff | hist) . . (+772) . . G-code (Add M408, M409 in Marlin 2.0)
- 15:30, 19 October 2018 (diff | hist) . . (+360) . . G-code (Add M524)
- 18:08, 12 October 2018 (diff | hist) . . (+119) . . G-code (→M217: Toolchange Parameters: Add XYZ parameters)
- 14:53, 7 October 2018 (diff | hist) . . (+628) . . G-code (Add M217 for Marlin 2.0)
- 20:06, 5 October 2018 (diff | hist) . . (+417) . . Firmware Capabilities Protocol (Add PAREN_COMMENTS and MOTION_MODES)
- 04:07, 27 April 2018 (diff | hist) . . (+10) . . m Firmware Capabilities Protocol (→Cap:LEVELING_DATA)
- 03:52, 27 April 2018 (diff | hist) . . (+1,010) . . Firmware Capabilities Protocol (Add Marlin's current suite of capabilities)
- 02:47, 13 April 2018 (diff | hist) . . (+229) . . G-code (→M18: Disable all stepper motors: Marlin synonym of M84)
- 01:27, 16 March 2018 (diff | hist) . . (+504) . . G-code (→M27: Report SD print status: Add 'S' parameter)
- 01:16, 16 March 2018 (diff | hist) . . (+172) . . G-code (→M27: Report SD print status: New 'C' parameter)
- 20:41, 15 February 2018 (diff | hist) . . (+19) . . G-code (→M106: Fan On: Note on Marlin change.)
- 15:04, 5 January 2018 (diff | hist) . . (+85) . . m G-code (→M504: Validate EEPROM)
- 14:14, 5 January 2018 (diff | hist) . . (+1) . . m G-code (→M503: Print settings)
- 13:53, 5 January 2018 (diff | hist) . . (+491) . . G-code (Add M504, M503 S0)
- 20:07, 20 October 2017 (diff | hist) . . (+1) . . m G-code (→M280: Set servo position: as with previous)
- 20:06, 20 October 2017 (diff | hist) . . (+12) . . m G-code (→M280: Set servo position: format code)
- 20:04, 20 October 2017 (diff | hist) . . (+40) . . m G-code (→M290: Babystepping: M290 Z synonym)
- 20:02, 20 October 2017 (diff | hist) . . (+9) . . m G-code (→M302: Allow cold extrudes: "and later" thanks to RepRapFirmware)
- 20:00, 20 October 2017 (diff | hist) . . (0) . . m G-code (Fix search-replace glitch)
- 19:56, 20 October 2017 (diff | hist) . . (+483) . . G-code (Versions appear in tables now…)
- 17:52, 19 October 2017 (diff | hist) . . (+1) . . G-code (Update M290, plus version indicators)
- 00:43, 7 October 2017 (diff | hist) . . (+162) . . N Talk:MKS 12864OLED (Clarificiation prior to updating the page for Marlin 1.1+.) (current)
- 02:00, 28 June 2017 (diff | hist) . . (+380) . . G-code (→M118: Negotiate Features: Marlin 1.1.4 uses this code)
- 00:10, 28 June 2017 (diff | hist) . . (+209) . . N User talk:Thinkyhead (Created page with "I propose replacing this with extensions to M115 with the extended capabilities report. These are similar, except perhaps more protocol-related. M118 could be useful for somet...") (current)
- 20:53, 25 June 2017 (diff | hist) . . (+465) . . G-code (→G17..19: Plane Selection (CNC specific): Update on G17-G19)
- 03:55, 17 June 2017 (diff | hist) . . (+7) . . m G-code (→G0 & G1: Move: format/descriptions of examples)
- 04:49, 23 May 2017 (diff | hist) . . (+41) . . G-code (→G42: Move to Grid Point: Add 'F' param to G42)
- 04:39, 23 May 2017 (diff | hist) . . (+98) . . m G-code (→G42: Move to Grid Point: M42 - more firmwares)
- 04:35, 23 May 2017 (diff | hist) . . (0) . . m G-code (→G42: Move to Grid Point: ditto)
- 04:33, 23 May 2017 (diff | hist) . . (+1) . . m G-code (→G42: Move to Grid Point: space after 'yes' label)
- 04:30, 23 May 2017 (diff | hist) . . (+708) . . G-code (Add Marlin's M42, prevent eyeroll in G33)
- 00:04, 11 May 2017 (diff | hist) . . (+8) . . m G-code (→G26: Mesh Validation: "pattern")
- 21:36, 10 May 2017 (diff | hist) . . (-10) . . m G-code (→G29 Unified Bed Leveling (Marlin): tweak ubl parameters)
- 21:31, 10 May 2017 (diff | hist) . . (-22) . . m G-code (→G29 Auto Bed Leveling (Marlin): formatting)
- 20:30, 10 May 2017 (diff | hist) . . (-75) . . m G-code (→G29 Unified Bed Leveling (Marlin): correction)
- 20:27, 10 May 2017 (diff | hist) . . (+4,154) . . G-code (Add M80 S, G26, and G29 UBL documentation)
- 05:03, 17 April 2017 (diff | hist) . . (+2) . . m G-code (Fix typo in code closing tag)
- 04:58, 17 April 2017 (diff | hist) . . (+10,608) . . G-code (Add M900, format most G-codes with <code> tags)
- 23:43, 21 November 2016 (diff | hist) . . (+56) . . G-code (→G29 Auto Bed Leveling in Marlin: recommend bilinear)
- 23:39, 21 November 2016 (diff | hist) . . (+1,505) . . G-code (→G29: Detailed Z-Probe: Updated details for Marlin G29)
- 22:59, 21 November 2016 (diff | hist) . . (+1,060) . . G-code (→G28: Move to Origin (Home): Improve and extend G28)
- 18:18, 21 November 2016 (diff | hist) . . (+207) . . m G-code (Specify mk4duo support for remaining codes)
- 18:02, 21 November 2016 (diff | hist) . . (+16) . . m G-code (→M585: Probe Tool: mk4duo)
- 18:01, 21 November 2016 (diff | hist) . . (+15) . . m G-code (→M851: Set Z-Probe Offset: mk4duo)
(newest | oldest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)