All public logs
Combined display of all available logs of RepRap. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).
(newest | oldest) View (newer 20 | older 20) (20 | 50 | 100 | 250 | 500)- 22:46, 13 December 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel Y-axis belt holder Lahuerta 1a.jpg (Simple Y-axis GT2 Belt Holder for the P3Steel designed by Pedro Lahuerta which is easy to print, easy to install and works very well.)
- 22:32, 13 December 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel useless part 1a.jpg (Useless part removed in version 2.01 of the P3Steel frame.)
- 19:03, 13 December 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel x-axis 1a.jpg (The P3Steel X-axis assembly with a specific combination of Vitamins (the printed parts).)
- 08:17, 13 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis belt holder 5a.JPG (The GT2 belt and holder properly installed under the heatbed and Y-carriage.)
- 16:05, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 3a.jpg (Y-axis carriage assembled, top view.)
- 15:53, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis motor end 8a.JPG (If you look carefully at where the arrow is pointing you can see the interference between the stepper and the nyloc nut, and where the stepper body has been filed away slightly.)
- 14:52, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 13b.jpg (Guiding the smooth rod into the frame support, detail.)
- 14:43, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 16a.jpg (Done tapping here too (front right).)
- 14:33, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 15a.jpg (Back left rod seems OK. We are definitely done tapping here!)
- 14:25, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 14a.jpg (We are done here (front left)!)
- 14:19, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 13a.jpg (Only 3mm left for this rod. M-u-s-t--t-a-p--m-o-r-e...)
- 13:51, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 12a.jpg (We must guide the smooth rods into their corresponding slots manually as we tap them in for the last few millimeters.)
- 08:34, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 11a.jpg (We can slide the Y-carriage back in place once the smooth rods have been pushed in far enough.)
- 08:27, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 10a.jpg (Patience! Go on tapping with the hammer...)
- 08:19, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 9a.jpg (Continuing with the tapping, the rods will progressively move into the frame.)
- 06:48, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 8a.jpg (Tapping the rod ends gently with the hammer, push them through their supports on the P3Steel frame. We can slide out the Y-carriage now.)
- 06:36, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Ramps fan bracket2a.jpg (Arduino Mega 2560 + RAMPS 1.4 + 80mm fan stack powered on.)
- 05:04, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 4a.jpg (While holding the Y carriage horizontal, manually engage the two smooth rods in the back supports.)
- 03:09, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 1a.jpg (The Y-carriage with the 8mm smooth rods and the GT2 belt holder installed.)
- 02:19, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis motor end 7a.JPG (The Y-axis stepper and GT2 pulley installed.)