Smartrap Build Manual
English • العربية • български • català • čeština • Deutsch • Ελληνικά • español • فارسی • français • hrvatski • magyar • italiano • română • 日本語 • 한국어 • lietuvių • Nederlands • norsk • polski • português • русский • Türkçe • українська • 中文(中国大陆) • 中文(台灣) • עברית • azərbaycanca • |
Smartrap Mini | How to Get Smartrap | Smartrap Build Manual | How to Use Smartrap | Smartrap Improvements
Welcome to the official document of the Smartrap's assembly.
This is the assembly manual for the Smartrap V 0.4.9 serie. For little changes between versions, we add extra steps.
Each step of building should take around one minute.
Contents
Tools you need:
- Small screwdriver plate for M3
- Bigger screwdriver for M6
- Allen key 1mm
Printed parts
![]() |
plate_base 049 | ![]() |
plate_x 049 | ![]() |
plate_y | ||
![]() |
bottom 049 | ![]() |
endx_huxley | ![]() |
endx_back | ||
![]() |
glass_holder | ![]() |
glass_support | ![]() |
z_coupler 049 | ||
![]() |
direct_drive | ![]() |
belt_axis | ![]() |
belt_tensioner |
Updated parts 0.4.9.2
Non printed parts
Pre-assemble the Huxley head 049
If you received a jhead lite, please jump this step.
![]() |
1 | ![]() |
2 | ![]() |
3 |
![]() |
4 | ![]() |
5 | ![]() |
6 |
![]() |
7 | ![]() |
8 | ![]() |
9 |
![]() |
10 |
Bottom / base
![]() |
1 | ![]() |
2 | ![]() |
3 |
![]() |
4 | ![]() |
5 | ![]() |
6 |
![]() |
7 | ![]() |
8 | ![]() |
9 |
![]() |
10 | ![]() |
11 | ![]() |
12 |
![]() |
13 |
Y axis
![]() |
1 | ![]() |
2 | ![]() |
3 |
![]() |
4 | ![]() |
5 | ![]() |
6 |
![]() |
7 | ![]() |
8 | ![]() |
9 |
![]() |
10 | ![]() |
11 | ![]() |
12 |
![]() |
13 | ![]() |
14 | ![]() |
15 |
![]() |
16 | ![]() |
17 | ![]() |
18 |
![]() |
19 | ![]() |
20 | ![]() |
21 |
![]() |
22 |
Extruder
![]() |
1 | ![]() |
2 | ![]() |
3 |
![]() |
4 | ![]() |
5 | ![]() |
6 |
![]() |
7 |
X axis
![]() |
1 | ![]() |
2 | ![]() |
3 |
![]() |
4 | ![]() |
5 | ![]() |
6 |
![]() |
7 | ![]() |
8 | ![]() |
9 |
![]() |
10 | ![]() |
11 | ![]() |
12 |
![]() |
13 | ![]() |
14 | ![]() |
15 |
![]() |
16 |
Z axis
![]() |
1 | ![]() |
2 | ![]() |
3 |
![]() |
4 | ![]() |
5 | ![]() |
6 |
![]() |
7 | ![]() |
8 | ![]() |
9 |
![]() |
10 |
Wiring
First , here is the electronics card mapping.
NOTES: if using a huxley , please use the D9 connection. If using a jhead lite, please use the two first pins of Zmax stop. It is just to use +5v and ground. It will then turn to the right speed , always ( no need to control in software).
We use the most standard controler in thereprap world because you can find a lot of documentation about it : look for ramps 1.4 in your search and you will find tons of infos, forum, trics..etc.
![]() |
1 | ![]() |
2 | ![]() |
3 |
![]() |
4 | ![]() |
5 | ![]() |
6 |
![]() |
7 | ![]() |
8 | ![]() |
9 |
![]() |
10 | ![]() |
11 | ![]() |
12 |
![]() |
13 | ![]() |
14 | ![]() |
15 |
![]() |
16 | ![]() |
17 | ![]() |
18 |
![]() |
19 | ![]() |
20 | ![]() |
21 |
![]() |
22 | ![]() |
23 | ![]() |
24 |
Finishing
![]() |
1 | ![]() |
2 | ![]() |
3 |
![]() |
4 | ![]() |
5 | ![]() |
6 |