All public logs
Combined display of all available logs of RepRap. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).
(newest | oldest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)- 04:28, 29 January 2015 AndrewBCN (talk | contribs) uploaded File:Rostock Delta Kinematics 3.pdf (A simple, clear explanation of the forward and reverse kinematics for linear delta printers, by Steve Graves.)
- 18:47, 13 January 2015 AndrewBCN (talk | contribs) uploaded File:Heatbed glass clips 1a.jpg (PCB heatbed mounted on P3Steel (Prusa i3 variant) with glass and bulldog clips.)
- 07:40, 11 January 2015 AndrewBCN (talk | contribs) uploaded File:A4988 detail current sense r 1a.jpg (A4988 clone board 0.1 Ohm current sense resistors detail.)
- 11:51, 7 January 2015 AndrewBCN (talk | contribs) uploaded File:Octogoatbox hardware TV Box 1a.jpg (Android TV Box assimilated by OctoGoat and converted to OctoGoatBox.)
- 11:02, 7 January 2015 AndrewBCN (talk | contribs) uploaded File:Octogoatbox hardware Banana Pi 2a.jpg (Power supply (5V@2A) and inexpensive 640x480 USB webcam.)
- 10:41, 7 January 2015 AndrewBCN (talk | contribs) uploaded File:Octogoatbox hardware Banana Pi 1a.jpg (Banana Pi, WiFi dongle, SD card and Octogoat.)
- 08:01, 26 December 2014 AndrewBCN (talk | contribs) uploaded File:ATX cable extension 24 fem to male 3a.jpg (Our 24-pin ATX extension cable prepared for use, the remaining lines carry the signals/voltages required to properly connect the ATX PSU to our RAMPS board.)
- 07:49, 26 December 2014 AndrewBCN (talk | contribs) uploaded File:ATX cable extension 24 fem to male 2a.jpg (The female connector of our 24-pin ATX extension cable plugged into the ATX PSU's male connector, after I yanked out all the lines that are not going to be used.)
- 06:59, 26 December 2014 AndrewBCN (talk | contribs) uploaded File:ATX 4to8pin adapter cable 2a.jpg (The ATX PSU female 4 pin to male 8 pin adapter cable, prepared for use. I just yanked the cables out of the male end, bunched respectively the +12V and GND lines together, and soldered the ends.)
- 06:50, 26 December 2014 AndrewBCN (talk | contribs) uploaded File:ATX 4to8pin adapter cable 1a.jpg (The ATX PSU female 4 pin to male 8 pin adapter cable. We only use the female connector.)
- 06:42, 26 December 2014 AndrewBCN (talk | contribs) uploaded File:ATX extension adapter cables ready 1a.jpg (The pair of cables needed to adapt an ATX PSU for Reprap use, ready for use!)
- 06:23, 26 December 2014 AndrewBCN (talk | contribs) uploaded File:ATX extension adapter cables 1a.jpg (A pair of cables needed to adapt an ATX PSU for Reprap use.)
- 12:51, 24 December 2014 AndrewBCN (talk | contribs) uploaded File:AndrewBCN-X-motor-end-4a.png (Prusa i3 X motor end improved by yours truly.)
- 12:49, 24 December 2014 AndrewBCN (talk | contribs) uploaded File:AndrewBCN-X-motor-end-3a.png (Prusa i3 X motor end improved by yours truly.)
- 09:40, 22 December 2014 AndrewBCN (talk | contribs) uploaded File:Stepper drivers mixed a4988 drv8825 RAMPS 1a.jpg (Mixing A4988 and DRV8825 stepper drivers on the same RAMPS 1.4? Yes, you can!)
- 07:31, 21 December 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel ramps printing 2a.jpg (Arduino Mega 2560 + RAMPS 1.4 + 4 x A4988 stepper drivers + 80mm fan stack, during a print.)
- 07:06, 21 December 2014 AndrewBCN (talk | contribs) uploaded File:Stepper drivers a4988 drv8825 4a.jpg (A4988 and DRV8825 stepper driver boards, underside.)
- 21:41, 19 December 2014 AndrewBCN (talk | contribs) uploaded File:Stepper drivers a4988 drv8825 3a.jpg (A4988 and DRV8825 stepper driver boards side by side.)
- 21:07, 19 December 2014 AndrewBCN (talk | contribs) uploaded File:Inexpensive stepper driver board a4988 1a.jpg (An inexpensive "Made in China" Pololu-style stepper driver board based on the popular Allegro 4988 IC.)
- 20:57, 19 December 2014 AndrewBCN (talk | contribs) uploaded File:RAMPS 1.4 1b.jpg (Inexpensive "Made in China" RAMPS 1.4 board without stepper driver boards.)
- 14:06, 19 December 2014 AndrewBCN (talk | contribs) uploaded File:DRV8825 stepper driver module 1a.jpg (DRV8825-based inexpensive stepper driver board.)
- 18:04, 17 December 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel x-axis motor end 2a.jpg (P3Steel Improved X motor end by AndrewBCN.)
- 17:40, 17 December 2014 AndrewBCN (talk | contribs) uploaded File:AndrewBCN-X-motor-end-1a.png (Reverse-engineered, improved Prusa i3 X motor end by AndrewBCN.)
- 17:06, 17 December 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel x-axis motor end 1a.jpg (X motor end complete.)
- 16:48, 17 December 2014 AndrewBCN (talk | contribs) uploaded File:BQ-X-motor-end-1a.png (This is bq's version of the Prusa i3 X motor end for their Prusa i3 Hephestos.)
- 15:55, 17 December 2014 AndrewBCN (talk | contribs) uploaded File:Mecan0-X-motor-end-1a.png (Mecan0's version of the Prusa i3 X motor end.)
- 15:42, 17 December 2014 AndrewBCN (talk | contribs) uploaded File:Misan-Improved-X-motor-end.png (Misan's version of the X motor end with a few added cutouts.)
- 15:14, 17 December 2014 AndrewBCN (talk | contribs) uploaded File:Misan-X-motor-end.png (Misan's improved Prusa i3 X motor end.)
- 15:04, 17 December 2014 AndrewBCN (talk | contribs) uploaded File:Josef-Prusa-Vanilla-X-motor-end-1a.png (Josef Prusa's original Prusa i3 vanilla X motor end.)
- 23:54, 13 December 2014 AndrewBCN (talk | contribs) uploaded File:PRUSA i3 steel 3mm lasercut 2.01d irobri color.jpg (For reference only. Low-res drawing of P3Steel version 2.01.)
- 22:46, 13 December 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel Y-axis belt holder Lahuerta 1a.jpg (Simple Y-axis GT2 Belt Holder for the P3Steel designed by Pedro Lahuerta which is easy to print, easy to install and works very well.)
- 22:32, 13 December 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel useless part 1a.jpg (Useless part removed in version 2.01 of the P3Steel frame.)
- 19:03, 13 December 2014 AndrewBCN (talk | contribs) uploaded File:P3Steel x-axis 1a.jpg (The P3Steel X-axis assembly with a specific combination of Vitamins (the printed parts).)
- 08:17, 13 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis belt holder 5a.JPG (The GT2 belt and holder properly installed under the heatbed and Y-carriage.)
- 16:05, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 3a.jpg (Y-axis carriage assembled, top view.)
- 15:53, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis motor end 8a.JPG (If you look carefully at where the arrow is pointing you can see the interference between the stepper and the nyloc nut, and where the stepper body has been filed away slightly.)
- 14:52, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 13b.jpg (Guiding the smooth rod into the frame support, detail.)
- 14:43, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 16a.jpg (Done tapping here too (front right).)
- 14:33, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 15a.jpg (Back left rod seems OK. We are definitely done tapping here!)
- 14:25, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 14a.jpg (We are done here (front left)!)
- 14:19, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 13a.jpg (Only 3mm left for this rod. M-u-s-t--t-a-p--m-o-r-e...)
- 13:51, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 12a.jpg (We must guide the smooth rods into their corresponding slots manually as we tap them in for the last few millimeters.)
- 08:34, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 11a.jpg (We can slide the Y-carriage back in place once the smooth rods have been pushed in far enough.)
- 08:27, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 10a.jpg (Patience! Go on tapping with the hammer...)
- 08:19, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 9a.jpg (Continuing with the tapping, the rods will progressively move into the frame.)
- 06:48, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 8a.jpg (Tapping the rod ends gently with the hammer, push them through their supports on the P3Steel frame. We can slide out the Y-carriage now.)
- 06:36, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Ramps fan bracket2a.jpg (Arduino Mega 2560 + RAMPS 1.4 + 80mm fan stack powered on.)
- 05:04, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 4a.jpg (While holding the Y carriage horizontal, manually engage the two smooth rods in the back supports.)
- 03:09, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis carriage 1a.jpg (The Y-carriage with the 8mm smooth rods and the GT2 belt holder installed.)
- 02:19, 11 December 2014 AndrewBCN (talk | contribs) uploaded File:Y-axis motor end 7a.JPG (The Y-axis stepper and GT2 pulley installed.)