1 0.1uF capacitor -------- Radioshack

  1 200-300mm of nichrome wire with a resistance of about 8 ohms ----- RRRF

  1 35mm piece of 10mm diameter PTFE rod with a 3mm hole drilled down the centre 8546K42

  1 40mm long piece of M6 brass bolt with a 3mm hole drilled right down the middle 93270A455 (10 per pack, only need one)

  7 608Z skate bearing -------RRRF? (I used 2 packs of metal balls (aka BBs), part #: 9292K38)
  1 625ZZNSK bearing --- 6153K69

  3 1200mm of 3.5mm ball chain (trade size 6) 3606T119
  1 2200mm of 4.5mm ball chain (trade size 10) 3606T121

  3 8mm i/d compression spring approximately 16mm long 9657K155
  4 small, stout springs ------------?
  
  8 M3 12mm screw 92005A122 
 29 M3 16mm screw 92005A126
 22 M3 20mm screw 92005A128
109 M3 25mm screw 92005A130
 16 M3 25mm screw NEMA17 92005A130
 13 M3 30mm screw 92005A132
 20 M3 40mm screw 92005A135 
  3 M3 50mm screw 92005A137 
 10 M5 25mm screw 92005A330 
 13 M5 30mm screw 92005A332 
  4 M5 50mm screw 92005A342 
  3 M8 25mm screw 92005A530 

197 M3 nut 90695A033
 50 M5 nut 90695A037
  4 M5 nut NEMA23 90695A037
 91 M8 nut 90591A161
  2 M8 nut ifstudding 90591A161

364 M3 washer 91166A210
 32 M3 washer NEMA17 91166A210
  4 large M3 washer 91100A120 
 32 M5 washer 91166A240
  8 M5 washer NEMA23 91166A240 
  1 M6 32mm o/d washer ----------? (local hardware store)
  2 M6 washer 91166A250 
 79 M8 washer 91166A270
  2 M8 wide aka fender washer 91100A160

 19 M5 8mm grub screw 91390A119

 10 M5 grub screw 91390A119 --------? (assuming this is also 8mm)

  2 M5 Nyloc nut 90576A114 
  1 M5 nyloc nut 90576A114 
  2 M8 nyloc nut 90576A117 

  2 M6 dome nut 91982A250 
  2 M6 half- or press-nut 90695A038 
  2 M8 half-nut 90591A161

 16 8mm diameter 500mm long bright steel rod 5544T27 (6 6ft lengths)
  4 M8 400mm studding 	93000A573 (5 2m lengths)
  1 M8 500mm studding 	93000A573 
  8 M8 600mm studding   93000A573 
  2 M8 650mm studding 	93000A573 
  2 M8 70mm studding ifstudding 93000A573 
  1 M8 80mm studding 	93000A573 
  1 M8 studding 110mm	93000A573

  1 PTFE tape 4591K11 

  1 gear motor RRRF

  2 hole socket strip ----- Radioshack

  1 thick, solid, insulated copper wire --- hardware store/Radioshack

  3mm drill bit 2958A61
  
  Cement 9372K22

  2 5mm i/d soft plastic tubing, approx 22mm long ----- Hardware store
-----------------------------------------------------